Skip to Content
Recent searches
      packshot front imea POLYBIT Polytherm AC meapackshot front imea POLYBIT Bituplus P4200 meapackshot front imea POLYBIT Bitustick P4180 mea

      Acrylic coatings (liquids)

      POLYBIT POLYTHERM AC
      Highly efficient, energy-saving flexible coating

      Water-based pure acrylic resin proving efficient thermal protection for the entire structure.
      • Durable & provides high degree heat insulation properties
      • Very high emittance & reflectance properties
      • Excellent dirt pick-up resistance over longer period of time

      TDS (1)

      SDSS (2)

      Request a consultation
      We have you covered
      Request a consultation

      Product Description

      POLYBIT® POLYTHERM AC applicable for: roofs, terraces, balconies, domes, etc; sandwich panels, corrugated sheets; refurbishing coating works on minerals surfaced waterproofing membranes; concrete facades. Available pack size: 20L pail.
      • Durable & provides high degree heat insulation properties
      • Very high emittance & reflectance properties
      • Excellent dirt pick-up resistance over longer period of time
      • Reduced thermal conductance and heat gain thereby by increasing energy efficiency
      • Outstanding adhesion over a variety of substrates
      • Waterproofing & resistance to blistering
      POLYBIT Polytherm AC frontside imea
      packshot front imea POLYBIT Polytherm AC meapackshot front imea POLYBIT Bituplus P4200 meapackshot front imea POLYBIT Bitustick P4180 mea

      How to Use

      Surface Preparation

      All the surfaces must be cleaned and made free of dust, dirt, moss, oil, grease and other loose particles. All pot holes and surface defects shall be repaired with a suitable concrete repair mortar from the Polycrete* range. Polytherm AC does not require priming and can directly be applied onto the surface. In case of highly porous surface, a priming coat is recommended to seal the pores and stabilize the surface. The primer coat can be produced on site by diluting Polytherm AC 1 to 1 with water. Apply the primer coat @ 5m2/L and allow to dry.

      Application

      Once stirred, Polytherm AC should be immediately applied either by brush, roller or industrial sprayer. It is recommended that coating be applied in a minimum of two coats. Should not be applied if relative humidity exceeds 95%. Each subsequent coat shall be applied only after the previous coat dries off completely. After application the coating must be back rolled to reduce surface irregularities and improve bonding.

      Finishing

      Store in a cool, dry place and keep away from all sources of heat and sunlight. In tropical climates, store in air condition rooms. The shelf life is up to 12 months in unopened condition and if stored as per recommendations. Excessive exposure to sunlight, humidity and UV will result in the deterioration of the quality of the product and reduce its shelf life.

      Frequently asked questions

      This is a water based pure acrylic resin coating

      There is no special primer. Primer can be prepared at site by diluting this with clean sweet water in the ratio 1:1 by volume.

      Yes. It is a UV resistant coating suitable for exposed applications

      Works Well With
      • ${/content/heliux/adhesive/polybit/com/en/products/waterproofing-solutions/acrylic-coatings-liquids/product#/polybit-polycryl/SAP_0201WPP34GH2/searchResult.productFields.MainImageAltText}
        POLYBIT Polycryl

        Superior grade, single component; pure acrylic based waterproofing and protective coating for concrete & masonry surfaces. the coating is durable, flexible and has a high resistance to UV. The coating is suitable for both interior and exterior application. 
      • ${/content/heliux/adhesive/polybit/com/en/products/waterproofing-solutions/acrylic-coatings-liquids/product#/polybit-polytex-s/SAP_0201WPP346X4/searchResult.productFields.MainImageAltText}
        POLYBIT POLYTEX S

        Superior grade, single component, acrylic based, waterproof coating with high elastomeric properties. It is durable, flexible and has a high level of resistance to weathering agents like UV, sunlight and rain. 
      • ${/content/heliux/adhesive/polybit/com/en/products/waterproofing-solutions/pu-coatings-special-liquids/product#/polybit-polythane-p/SAP_0201WVP345J6/searchResult.productFields.MainImageAltText}
        POLYBIT POLYTHANE P

        A liquid applied waterproofing and protective coating for concrete structures based on a hybrid polyurethane and free from coal tar and other hazardous ingredients. 

      Related Articles
      View all
      • Bitustick Cool

        The Next Generation of Performed Bituminous Coatings 
      • Foundations and Flooring Systems

        Discover, feel and touch our systems, through our mockup simulation boxes 
      • Wet Areas and Flooring Systems

        Discover, feel and touch our systems, through our mockup simulation boxes 
      • Polycryl FR

        The Ultimate Fire Rated Coating Solution 
      • Polycryl PF

        Strong UV protection For Polyurethane Foam Roof  
      • Bituplus Ultra

        The Ultimate Torch On Membrane Range 
      Sketch and drafting of a cozy house becoming real

      POLYBIT POLYTHERM AC IS PART OF OUR BIM MODELS

      Building Information Modeling (BIM) is an innovative approach to the planning, design, construction, and management of buildings and infrastructure. This smart model is a common source of knowledge for obtaining information about a building and provides a reliable basis for decision-making throughout the entire life cycle of a building, from conception to demolition.
      FIND OUT MORE
      Polybit Logo
      PRODUCTS
      SYSTEMS
      REFERENCES
      INNOVATION
      KNOWLEDGE
      CONTACT
      ABOUT
      SERVICE & SUPPORT

      © 2026 Henkel Polybit Industries Limited