Skip to Content
Recent searches
      packshot front imea POLYBIT polypoxy nf

      Concrete repair

      POLYBIT POLYCRETE PF
      Polymer modified cementitious fairing coat

      It is a single component polymer modified fairing coat to fill pores, blowholes, minor honeycombs on a concrete surface. This can also be used as a skim coat prior to the application of protective coatings.
      • Requires only on site addition of water
      • Shrinkage compensated and crack resistant
      • Excellent adhesion to concrete

      TDS (1)

      SDSS (2)

      Request a consultation
      We have you covered
      Request a consultation

      Product Description

      POLYBIT® POLYCRETE PF can be used as a skim coat and as an aesthetic mortar; To repair and fill honeycomb, concrete blowholes, etc; To repair patches, shutter movement damages and grout loss; To repair and fill undulations on steel surface; As surface preparation prior to the application of protective coatings. Available pack size: 25kg bag.
      • Requires only on site addition of water
      • Shrinkage compensated and crack resistant
      • Excellent adhesion to concrete
      • Easy to apply
      • Low permeability, resistant to the attacks of
        chlorides and other mild chemicals
      POLYBIT polycrete pf mea teaser
      packshot front imea POLYBIT polypoxy nf

      How to Use

      SUBSTRATE PREPARATION

      Clean the concrete surface of all contaminants like oil and grease, traces of curing compound and loosely adhering particles. The cleaning can be done by sand / grit blasting, high pressure water jet or mechanical scabbling. Saturate the concrete surface with clean potable water prior to the application of the fairing coat. However, ensure that the surface is free of standing water prior to the application of the fairing coat.

      APPLICATION

      POLYCRETE PF shall be mixed with 4.5 – 5.0 ltr. Water at a W/P ratio of 0.18 – 0.2. Pour the required quantity of water in a separate mixing container. Slowly add the powder to the water and mix continuously with a mortar paddle mixer fitted to a slow speed drill (300/400 rpm) till a homogeneous and lump free consistency is achieved. Apply the mixed mortar with a steel trowel evenly on to the concrete surface within its working time. Allow the coat to partly set before finally troweling it to achieve a smooth finish. For achieving a very smooth finish, sprinkle water on the surface and smoothen the surface with the steel trowel. The fairing coat shall be finished by striking off with a straight edge and closed with a steel or plastic float.

      CAUTION

      Due to the presence of rapid drying polymers in the fairing coat, the applied mortar has to be protected from hot and drying winds. Curing can be done either by the use of a non-degradable type of curing compound or continuous wetting of the surface with water. When cured with wet hessian cloth, the area shall be covered immediately with a high density polyethylene sheet which shall be taped to all the edges which has been repaired.

      Frequently asked questions

      It is not mandatory to use any bonding agent or primer for the new concrete. Only surface saturation is required with clean sweet water. But no logged water.

      Acrylic/PVA/SBR/Epoxy based bonding agents are recommended depending on the condition of the substrate.

      Yes. It is a shrinkage compensated product

      Works Well With
      • ${/content/heliux/adhesive/polybit/com/en/products/mortars-and-auxiliaries/concrete-repair/product#/polybit-polycrete-fc/SAP_0201VLP34GG9/searchResult.productFields.MainImageAltText}
        POLYBIT Polycrete FC

        Polymer modified cementitious fairing coat single component polymer modified fairing coat designed to fill pores, blowholes, minor honeycombs on a concrete surface. 
      • ${/content/heliux/adhesive/polybit/com/en/products/mortars-and-auxiliaries/concrete-repair/product#/polybit-polycrete-fcx/SAP_0201VLP345G6/searchResult.productFields.MainImageAltText}
        POLYBIT POLYCRETE FCX

        Polymer modified cementitious fairing coat to fill pores, blowholes, minor honeycombs on a concrete surface. 

      Related Articles
      View all
      • Bitustick Cool

        The Next Generation of Performed Bituminous Coatings 
      • Foundations and Flooring Systems

        Discover, feel and touch our systems, through our mockup simulation boxes 
      • Wet Areas and Flooring Systems

        Discover, feel and touch our systems, through our mockup simulation boxes 
      • Polycryl FR

        The Ultimate Fire Rated Coating Solution 
      • Polycryl PF

        Strong UV protection For Polyurethane Foam Roof  
      • Bituplus Ultra

        The Ultimate Torch On Membrane Range 
      Sketch and drafting of a cozy house becoming real

      POLYBIT POLYCRETE PF IS PART OF OUR BIM MODELS

      Building Information Modeling (BIM) is an innovative approach to the planning, design, construction, and management of buildings and infrastructure. This smart model is a common source of knowledge for obtaining information about a building and provides a reliable basis for decision-making throughout the entire life cycle of a building, from conception to demolition.
      FIND OUT MORE
      Polybit Logo
      PRODUCTS
      SYSTEMS
      REFERENCES
      INNOVATION
      KNOWLEDGE
      CONTACT
      ABOUT
      SERVICE & SUPPORT

      © 2026 Henkel Polybit Industries Limited