Skip to Content

POLYBIT POLYPUR TC 20

UV stable, polyurethane car park deck coating

  • Highly durable and UV stable
  • Excellent abrasion resistance
  • Good chemical resistance

Features and benefits

Two component high quality polyurethane car park deck coating system for both internal and external areas.

Properties

Description

POLYBIT® POLYPUR TC 20 is a protective and wear resistant coating for new and existing trafficked areas such as: car park decks and ramps; plant rooms; trafficable flat roofs; terraces and balconies; chemical processing areas; factory ware houses. Available pack size: 5L kit, 15L kit.

Documents and downloads

How to use

Surface Preparation

The surface should be dry, free of any cement laitance, oil and grease, curing compound and any other contaminants, which may affect the bonding. New concrete surfaces should be 28 days old and the moisture content on the surface must be less than 5%. Surface irregularities and blow holes shall be repaired with Polypoxy BF or Polycrete ST. The surface should be vacuumed ahead of priming. Prime the prepared surface with Polyprime PU @ 4-5m2/L. The coating is applied when the primer is dry. However, in all circumstances, the coating shall be applied within 24 hours of application of the primer. If the primer surface is left open for more than 24 hours, then a fresh coat of primer has to be re-applied. Broadcast Aggregate No. 3 on the primer whilst it is still wet @0.3 kg/m2. On ramp and turning areas, the aggregate shall be broadcasted @1.2-1.5 kg/m2. After the primer dries off brush away or vacuum out the excess aggregates.

Application

Top coat Polypur TC 20 shall be applied as the abrasion resistant top coat. This UV resistant coating is supplied in two preweighed packs (resin & hardener). Stir both components seperately for a minut to remove any sediments. Slowly add the hardener (B) into the resin (A) and mix thoroughly with a slow speed drill with a proprietary paddle mixer for 2 -3 minutes, until a homogenous consistency is obtained. Work the mixer round the mixing pan to ensure it scrapes the side and bottom of the pail. Once the material is mixed immediately apply the coating with a roller or airless spray at a coverage rate of 5m2/L. If required apply a second coat at the same coverage rate and only after the first coat has dried off completely (24 hours). The coating will achieve its full mechanical properties after 7 days of cure, after which the floor can be subjected to heavy traffic. 

Finishing

Store all material in a cool, covered dry place. Do not expose the pails to direct sunlight and keep away from all sources of heat. In tropical climatic conditions, the product has to be stored in an airconditioned environment and protected from high humidity. The shelf life of the product is 12 months in unopened condition if stored as per the recommendations. Exposure to high temperature and humidity will result in considerable deterioration of the product and reduce its shelf life. 

Related articles

  • Bitustick Cool

    The Next Generation of Performed Bituminous Coatings 

  • Foundations and Roofing Systems

    Discover, feel and touch our systems, through our mockup simulation boxes 

  • Wet Areas and Flooring Systems

    Discover, feel and touch our systems, through our mockup simulation boxes 

  • Polycryl FR

    The Ultimate Fire Rated Coating Solution 

  • Polycryl PF

    Strong UV protection For Polyurethane Foam Roof  

  • Bituplus Ultra

    The Ultimate Torch On Membrane Range 

Related products

  • ${/content/heliux/adhesive/polybit/com/en/products/central-pdp#/polybit-polypoxy-bf/SAP_0201TWP34GK0/searchResult.productFields.MainImageAltText}
    POLYBIT Polypoxy BF
    It is a two component, solvent free, epoxy based repair putty and mortar for concrete surfaces. The epoxy putty consists of graded fillers and non-sagging agents. It is designed for filling of blow holes, cracks and minor imperfections on concrete surfaces. 
  • ${/content/heliux/adhesive/polybit/com/en/products/central-pdp#/polybit-polypoxy-cr/SAP_0201WUP34GK1/searchResult.productFields.MainImageAltText}
    POLYBIT Polypoxy CR
    Solvent free high build epoxy resin protective coating which provides a chemical resistant surface for concrete and steel. 

Frequently asked questions

It is polyurethane based topcoat

Yes. It is a UV resistant product suitable for exposed use.

Approximately 125 microns dry film thickness. 1L can cover approximately 5 sqm/coat at this given DFT.