Skip to Content

POLYBIT Polygrout NS

Non-shrink free flow cementitious grout

  • Free flowing
  • Shrinkage compensated
  • Premixed and properly packed to avoid site variation
    and errors

Features and benefits

It is a cementitious non shrink grout which when mixed with water gives a free flowing shrinkage compensated grout of excellent workability and performance.

Properties

Description

POLYBIT® POLYGROUT NS is used for a machinery and equipment foundations; repair of pre–cast concrete; for anchoring of bolts, dowels etc; sealing of tie rod holes. Available pack size: 25kg bag.

Documents and downloads

How to use

SUBSTRATE PREPARATION

The surface should be clean, free of dust, demolding agents, oil, paint etc. Saturate the area to be grouted with water at least 24 hours prior to grouting. The surface should be damp, but strictly free of standing water. Whenever form work or shutter is used, make sure that all the joints are sealed properly to avoid grout loss.

APPLICATION

Mixing should be done using a drill fitted with a mixing paddle or a grout mixer. Add 2.75 - 3.25 liters of clean cool water in a container. Add Polygrout NS slowly and mix continuously for a minimum of 5 minutes to obtain a smooth, uniform lump free consistency.
Note: Unopened bags are to be kept in a shaded area water used for mixing should be below 25°C, particularly in high ambient temperature conditions.
Grouting should be done continuously. Therefore make sure that sufficient grout is prepared before starting. Polygrout NS can be poured from minimum 10mm up to 80mm in one single pour. However, for depths greater than 80mm it is recommended to add well graded aggregates of 5 to 8mm (up to 50%) to the grout in order to reduce the heat generated during the exothermic reaction when the grout is mixed and poured for larger depths. Cover the exposed areas immediately after placing with a polythene sheet, to protect from drying winds. 

STORAGE & SHELF LIFE

Store in a cool, dry place and keep away from all sources of heat and sunlight. In tropical climates, store in air condition rooms. The shelf life is up to 12 months in unopened condition and if stored as per recommendations. excessive exposure to sunlight, humidity and UV will result in the deterioration of the quality of the product and reduce its shelf life. 

Related articles

  • Bitustick Cool

    The Next Generation of Performed Bituminous Coatings 

  • Foundations and Roofing Systems

    Discover, feel and touch our systems, through our mockup simulation boxes 

  • Wet Areas and Flooring Systems

    Discover, feel and touch our systems, through our mockup simulation boxes 

  • Polycryl FR

    The Ultimate Fire Rated Coating Solution 

  • Polycryl PF

    Strong UV protection For Polyurethane Foam Roof  

  • Bituplus Ultra

    The Ultimate Torch On Membrane Range 

Related products

  • ${/content/heliux/adhesive/polybit/com/en/products/central-pdp#/polybit-polygrout-ey-3000-hs/SAP_0201VLP34GI6/searchResult.productFields.MainImageAltText}
    POLYBIT Polygrout EY 3000 (HS)
    A free flowing high strength non shrink solvent free epoxy resin based grout, which is used for grouting of machine base plate foundations, anchor bolts. 
  • ${/content/heliux/adhesive/polybit/com/en/products/central-pdp#/polybit-polygrout-ey-3000-ph/SAP_0201VLP34GI7/searchResult.productFields.MainImageAltText}
    POLYBIT Polygrout EY 3000 (PH)
    A three component solvent free epoxy based bedding grout and mortar used for pile head encapsulation. It is a combination of high performance epoxy resins, specially graded aggregates and additives to provide excellent mechanical properties. 
  • ${/content/heliux/adhesive/polybit/com/en/products/central-pdp#/polybit-polygrout-ey-3000-hf/SAP_0201VLP345I3/searchResult.productFields.MainImageAltText}
    POLYBIT POLYGROUT EY 3000 (HF)
    It is a free flowing non shrink solvent free low exothermic epoxy resin based grout. It is a combination of high performance epoxy resins, specially graded aggregates and additives withstand heavy static and dynamic loads in a wide variety of applications. Suitable for an application thickness up to 300mm. 

Frequently asked questions

This is a cementitious non-shrink grout

No priming required. Surface saturation is required with clean sweet water. But no logged water.

It can be applied at a thickness of 10 to 80mm/layer