Skip to Content

POLYBIT Polygrout EY 3000 (PH)

Pile head epoxy resin bedding grout and mortar

  • High compressive strength
  • Resistant to high temperature
  • Excellent chemical resistance

Features and benefits

A three component solvent free epoxy based bedding grout and mortar used for pile head encapsulation. It is a combination of high performance epoxy resins, specially graded aggregates and additives to provide excellent mechanical properties.



POLYBIT® POLYGROUT EY 3000 (PH) is used for a pile head encapsulation to ensure water tightness; bridge bearing pads; anchoring of crane rails, towers and dock sills; anchoring of bolts and rebars from 15mm - 60mm diameter in concrete, brick work, masonry and rock; installation of reinforced concrete starter bars, foundation bolts and railway tracks. Available pack size: 15L kit.

Documents and downloads

How to use


Surfaces shall be structurally sound and clean of all contaminants like mould release agent, curing compound, grease, paint and cement laitance. The area shall be dry and free of standing water. Surface cleaning by grit/captive blasting or wire brushing is recommended depending on the degree of contamination. A watertight shutter shall be erected all around the area where Polygrout EY 3000 (PH) shall be poured. Any gaps or openings below the formwork or on joints shall be sealed with a suitable mastic sealant or a rubber seal.
CAUTION: Resin leakage from the grout will result in segregation. The formwork shall be coated with a heavy duty mould release oil to ensure easy deshuttering.


Mix part a and part b separately for a minute using a slow speed drill (300 - 400 rpm) fitted to a suitable paddle mixer. Then add part b into part a and mix thoroughly for 1-2 minutes. Add part C aggregates slowly into the mix and further mix for another for 3-4 minutes till a uniform and homogenous consistency is achieved.
Note: All parts are pre-weighed and no part mixing is allowed.
Pour the mixed Polygrout EY 3000 (PH) immediately after mixing and within the pot life. The grout shall be poured continuously from one corner or side to avoid entrapment of air. Spread the poured grout evenly with a steel trowel. for congested areas it is recommended to lightly tamp the shutters with a rubber mallet to remove the entrapped air.
Note: The grout which has exceeded its pot life shall not be used and be discarded immediately. 


Store the material in a dry, cool and shaded condition. in tropical climates the product must be stored in an air– conditioned environment. The shelf life of the product is up to 12 months when stored as per recommendation. Excessive exposure to heat, UV and sunlight will result in the deterioration of the quality of the product and reduce its shelf life. 

Related articles

  • Bitustick Cool

    The Next Generation of Performed Bituminous Coatings 

  • Foundations and Roofing Systems

    Discover, feel and touch our systems, through our mockup simulation boxes 

  • Wet Areas and Flooring Systems

    Discover, feel and touch our systems, through our mockup simulation boxes 

  • Polycryl FR

    The Ultimate Fire Rated Coating Solution 

  • Polycryl PF

    Strong UV protection For Polyurethane Foam Roof  

  • Bituplus Ultra

    The Ultimate Torch On Membrane Range 

Related products

  • ${/content/heliux/adhesive/polybit/com/en/products/central-pdp#/polybit-polygrout-ey-3000-hs/SAP_0201VLP34GI6/searchResult.productFields.MainImageAltText}
    POLYBIT Polygrout EY 3000 (HS)
    A free flowing high strength non shrink solvent free epoxy resin based grout, which is used for grouting of machine base plate foundations, anchor bolts. 
  • ${/content/heliux/adhesive/polybit/com/en/products/central-pdp#/polybit-polygrout-ey-3000-hf/SAP_0201VLP345I3/searchResult.productFields.MainImageAltText}
    It is a free flowing non shrink solvent free low exothermic epoxy resin based grout. It is a combination of high performance epoxy resins, specially graded aggregates and additives withstand heavy static and dynamic loads in a wide variety of applications. Suitable for an application thickness up to 300mm. 
  • ${/content/heliux/adhesive/polybit/com/en/products/central-pdp#/polybit-polycrete-mc/SAP_0201VLP34GH0/searchResult.productFields.MainImageAltText}
    POLYBIT Polycrete MC
    High strength free flowing micro concrete suitable to repair large volume of concrete repairs at thicknesses from 10mm to 250mm. 

Frequently asked questions