POLYBIT POLYFLEX T

Flexible, Waterproofing and protective slurry mortar

  • Can be used on horizontal surfaces where light foot traffic is expected. (Balconies) – Interior and exterior waterproofing of basements. – Sealing of hairline cracks in concrete structures not subject to surface movement. – Can be used in waterproofing of drinking water tanks, reservoirs and clear wells. – Can be used for internal and external waterproofing and damp proofing concrete, mortar block work and brickwork.
  • Good abrasion resistance
  • Good abrasion resistance

Features and benefits

A superior grade, two - component, polymer modified cementitious waterproofing and protective slurry mortar for concrete.

Properties

Description

POLYBIT® POLYFLEX T Can be used on horizontal surfaces where light foot traffic is expected. (Balconies) Interior and exterior waterproofing of basements. Sealing of hairline cracks in concrete structures not subject to surface movement. Can be used in waterproofing of drinking water tanks, reservoirs and clear wells. Can be used for internal and external waterproofing and damp proofing concrete, mortar block work and brickwork. Available pack size: 25KG.

How to use

Surface Preparation

All the substrates must be dry and free of dust, dirt, moss,
oil, grease and loose particles. All surfaces must be as true
and flat as possible. This can be achieved by wire brushing
or grit blasting. Unsound surfaces are to be removed and
repaired with a suitable repair mortar.

Application

Polyflex T is supplied in two pre-measured parts which just
requires on site mixing. Do not mix more material than that
can be used within the pot life. Part mixing can be carried
out by mixing 4 volumes of powder with 1 volume of liquid
for Slurry consistency and 4.5 volumes of powder and 1
volume of liquid for a Trowelable consistency. 

Finishing

Polyflex T can be applied using trowel, notch trowel and
spray equipment. Work the material well into the prepared
substrate, filling all pores and voids. As with all cement based products, curing is important.
Protect newly applied product against direct sunlight, wind,
rain and frost. Allow a minimum 48 hours of air curing. 

Related articles

  • Bitustick Cool

    The Next Generation of Performed Bituminous Coatings 

  • Foundations and Roofing Systems

    Discover, feel and touch our systems, through our mockup simulation boxes 

  • Wet Areas and Flooring Systems

    Discover, feel and touch our systems, through our mockup simulation boxes 

  • Polycryl FR

    The Ultimate Fire Rated Coating Solution 

  • Polycryl PF

    Strong UV protection For Polyurethane Foam Roof  

  • Bituplus Ultra

    The Ultimate Torch On Membrane Range 

Related products

  • ${/content/heliux/adhesive/polybit/com/en/products/central-pdp#/polybit-polyflex/SAP_0201WJP34GI1/searchResult.productFields.MainImageAltText}
    POLYBIT Polyflex
    A two part acrylic modified cementitious coating for protecting concrete structures against water, vapor, ingress of chloride ions, attacks of acidic gases and alkalis. 
  • ${/content/heliux/adhesive/polybit/com/en/products/central-pdp#/polybit-polyflex-combo/SAP_0201WJP345H1/searchResult.productFields.MainImageAltText}
    POLYBIT POLYFLEX COMBO
    A two part acrylic modified cementitious coating for protecting concrete structures against water, vapor, ingress of chloride ions, attacks of acidic gases and alkalis. 
  • ${/content/heliux/adhesive/polybit/com/en/products/central-pdp#/polybit-polyflex-s/SAP_0201WJP34GI3/searchResult.productFields.MainImageAltText}
    POLYBIT Polyflex S
    A two part acrylic modified cementitious flexible water proofing system, especially designed for continually immersed conditions. 

Frequently asked questions

Yes. This can be applied on damp surface. But not on waterlogged area

No. Minimum 72 hours curing needed from the last coat.

Yes. It is a non-toxic product.