Skip to Content
Recent searches
      Bitustick R3000 packshot

      Bitumen-sam (membranes, primers)

      POLYBIT Bitustick R 3000
      Polyester reinforced, cross laminated high performance self-adhesive bituminous waterproofing membrane

      High performance self adhesive bituminous waterproofing membrane strengthened with a non woven polyester fabric laminated onto a top surfacing high
      density, cross laminated polyethylene film.
      • Cold applied self adhesive and easy to apply
      • Excellent adhesion to vertical and horizontal surfaces
      • Excellent resistance to aggressive soil conditions, ground water/salts and contaminated water

      TDS (1)

      SDSS (6)

      Certificate Public (1)

      Request a consultation
      We have you covered
      Request a consultation

      Product Description

      POLYBIT® BITUSTICK R 3000 membranes are predominantly used as waterproofing or damproofing membranes intended for concrete protection. It may be used for horizontal or vertical applications, and as a damproof course for tanking below ground structures, subways and retaining walls.
      Available pack size: 2mm & 3mm
      • Cold applied self adhesive and easy to apply
      • Excellent adhesion to vertical and horizontal surfaces
      • Excellent resistance to aggressive soil conditions, ground water/salts and contaminated water
      • Excellent tear and tensile strength
      • Water and vapor proof
      • Excellent puncture resistance and mechanical properties
      Bitustick R3000 packshot
      Bitustick R3000 packshot

      How to Use

      SURFACE PREPARATION

      As with any waterproofing membranes, proper application
      is of paramount importance to obtain optimum product
      performance. A smooth regular and dry surface is always
      a must for good application. The substrate should be
      completely free of any protrusions or cavities. The presence of oily materials, frost, dampness, moisture and any other
      contaminants should be completely removed.

      PRIMING

      Apply Polyprime SB* (solvent based primer) @ 4- 6 m²/L to
      a clean smooth and dry surface by brush, roller or spray.
      Allow the primer to dry prior to the application of the
      membrane. As the viscosity of the primer is low, it easily
      penetrates into the concrete pores which promotes the
      adhesion between the membrane and the concrete surface.
      In addition to that the primer also acts as a binder for the
      dust which gets accumulated on the concrete surface even

      APPLICATION

      1. Unroll only the required length, and cut the piece to the
      desired shape and size.
      2. Place the pieces of membrane on the area to be
      covered, and check whether they match with the profile
      of the marked substrate.
      3. Peel off release film and carefully place the membrane
      so as to ensure a minimum of 75mm overlap and then
      smoothen the membrane from the centre to the edges in
      order to drive out entrapped air.
      4. In case the concrete structure is at a greater depth or is
      going to be exposed to site conditions / weather for a
      long period, place Bituboard asphaltic protection board
      on top of the membrane soon after the application in
      order to prevent any damage to the membrane.

      Frequently asked questions

      It is recommended using solvent based bitumen primer conforming to ASTM D 41

      No. We recommend liquid applied waterproofing coatings for wet areas

      Yes. It msut be protected from damages that may happen during the site activities.

      Works Well With
      • ${/content/heliux/adhesive/polybit/com/en/products/waterproofing-solutions/bitumen-thin-coatings/product#/polybit-polyprime-sb/SAP_0201WEP345J0/searchResult.productFields.MainImageAltText}
        POLYBIT POLYPRIME SB

        A quick drying solvent based low viscosity bitumen primer. It is used as a primer coat on masonry and concrete substrates to improve the adhesion of bitumen based membranes and coatings. 
      • ${/content/heliux/adhesive/polybit/com/en/products/waterproofing-solutions/protection-membranes/product#/polybit-bituboard/SAP_0201W1P34GA5/searchResult.productFields.MainImageAltText}
        POLYBIT Bituboard

        A multi layer, asphaltic protection board manufactured by thermally bonding polymer modified bitumen with selected additives which, sandwiched between a layer of saturated fibre-glass on one side and anti-stick polyethylene liner on the other. 

      Related Articles
      View all
      • Bitustick Cool

        The Next Generation of Performed Bituminous Coatings 
      • Foundations and Flooring Systems

        Discover, feel and touch our systems, through our mockup simulation boxes 
      • Wet Areas and Flooring Systems

        Discover, feel and touch our systems, through our mockup simulation boxes 
      • Polycryl FR

        The Ultimate Fire Rated Coating Solution 
      • Polycryl PF

        Strong UV protection For Polyurethane Foam Roof  
      • Bituplus Ultra

        The Ultimate Torch On Membrane Range 
      Sketch and drafting of a cozy house becoming real

      POLYBIT Bitustick R 3000 IS PART OF OUR BIM MODELS

      Building Information Modeling (BIM) is an innovative approach to the planning, design, construction, and management of buildings and infrastructure. This smart model is a common source of knowledge for obtaining information about a building and provides a reliable basis for decision-making throughout the entire life cycle of a building, from conception to demolition.
      FIND OUT MORE
      Polybit Logo
      PRODUCTS
      SYSTEMS
      REFERENCES
      INNOVATION
      KNOWLEDGE
      CONTACT
      ABOUT
      SERVICE & SUPPORT

      © 2026 Henkel Polybit Industries Limited