Skip to Content
Recent searches
      Bitustick P packshot

      Bitumen-sam (membranes, primers)

      POLYBIT Bitustick P
      Polyester reinforced waterproofing membrane

      Polymer modified bitumen self adhesive bituminous waterproofing membrane.
      • Excellent adhesion to vertical and horizontal surfaces
      • High tensile and tear strength
      • Provides protection against water and vapor

      TDS (1)

      SDSS (8)

      Certificate Public (1)

      Request a consultation
      We have you covered
      Request a consultation

      Product Description

      POLYBIT® BITUSTICK P is used for waterproofing or dampproofing of concrete structures. It can be used in both horizontal and vertical applications for tanking below ground structures, subways and retaining walls.
      Available pack size: 1.6mm & 2mm
      • Excellent adhesion to vertical and horizontal surfaces
      • High tensile and tear strength
      • Provides protection against water and vapor
      • Good puncture resistance
      • Self adhesive
      • Excellent resistance to chlorides, sulphates, alkalis and acids
      Bitustick P packshot
      Bitustick P packshot

      How to Use

      SURFACE PREPARATION & PRIMING

      The surface shall be cleaned thoroughly of all contaminants like dust, traces of curing compound, oil and grease. All surface imperfections, protrusions, structurally unsoundand friable concrete must be removed and repaired with a suitable Polycrete* concrete repair mortar.
      Apply Polyprime SB* (solvent based primer) @ 4- 6 m²/L to a clean smooth and dry surface by brush, roller or spray.
      Allow the primer to dry prior to the application of the membrane. As the viscosity of the primer is low, it easily penetrates into the concrete pores which promotes the adhesion between the membrane and the concrete surface.
      In addition to that the primer also acts as a binder for the dust which gets accumulated on the concrete surface even after cleaning.

      ALIGNMENT & APPLICATION

      Start the installation of all membrane plies from the low point or drains, so that the flow of water is over or parallel to the plies, but never against the laps. All overlaps at the membrane seams shall be installed so as to have «up» slope laps over «down» slope laps. Begin membrane application by unrolling the roll of Bitustick P membrane and aligning the side laps.
      Peel off the release film from the self adhesive side and start unrolling the membrane and press it to the surface. Smoothen the membrane from the center to the edges with a wooden press in order to remove entrapped air. Furthermore, an iron roller shall be used for rolling on top of the applied membrane to ensure a proper and strong adhesion of the bitumen compound with the base surface. Side overlaps shall be a minimum of 50mm on the selvedge and end overlaps 100mm.

      PROTECTION

      The membrane shall be protected immediately after
      application from damage, due to ongoing site activities or
      from sharp aggregates during backfilling by a tough, weather,
      warp and rot proof asphaltic protection board (Bituboard /
      Bitustick R300/ Bitustick R400)*. Alternatively, on horizontal
      areas the membrane can also be protected by laying a
      cement sand screed (50mm). Bituboard can be fixed with a
      double sided adhesive bitumen tape (Bitutape TS)*.

      Frequently asked questions

      It is recommended using solvent based bitumen primer conforming to ASTM D 41

      No. We recommend liquid applied waterproofing coatings for wet areas

      It is a BBA certified product

      Works Well With
      • ${/content/heliux/adhesive/polybit/com/en/products/waterproofing-solutions/bitumen-thin-coatings/product#/polybit-polyprime-sb/SAP_0201WEP345J0/searchResult.productFields.MainImageAltText}
        POLYBIT POLYPRIME SB

        A quick drying solvent based low viscosity bitumen primer. It is used as a primer coat on masonry and concrete substrates to improve the adhesion of bitumen based membranes and coatings. 
      • ${/content/heliux/adhesive/polybit/com/en/products/waterproofing-solutions/protection-membranes/product#/polybit-bituboard/SAP_0201W1P34GA5/searchResult.productFields.MainImageAltText}
        POLYBIT Bituboard

        A multi layer, asphaltic protection board manufactured by thermally bonding polymer modified bitumen with selected additives which, sandwiched between a layer of saturated fibre-glass on one side and anti-stick polyethylene liner on the other. 
      • ${/content/heliux/adhesive/polybit/com/en/products/waterproofing-solutions/bitumen-tapes-membranes-flashing/product#/polybit-bitutape-ts/SAP_0201WCP34GD7/searchResult.productFields.MainImageAltText}
        POLYBIT Bitutape TS

        Bitutape TS is a non-reinforced twin side adhesive bitumen membrane which comprises of polymerized bitumen sandwiched between a plastic release film on either side. 

      Related Articles
      View all
      • Bitustick Cool

        The Next Generation of Performed Bituminous Coatings 
      • Foundations and Flooring Systems

        Discover, feel and touch our systems, through our mockup simulation boxes 
      • Wet Areas and Flooring Systems

        Discover, feel and touch our systems, through our mockup simulation boxes 
      • Polycryl FR

        The Ultimate Fire Rated Coating Solution 
      • Polycryl PF

        Strong UV protection For Polyurethane Foam Roof  
      • Bituplus Ultra

        The Ultimate Torch On Membrane Range 
      Sketch and drafting of a cozy house becoming real

      POLYBIT Bitustick P IS PART OF OUR BIM MODELS

      Building Information Modeling (BIM) is an innovative approach to the planning, design, construction, and management of buildings and infrastructure. This smart model is a common source of knowledge for obtaining information about a building and provides a reliable basis for decision-making throughout the entire life cycle of a building, from conception to demolition.
      FIND OUT MORE
      Polybit Logo
      PRODUCTS
      SYSTEMS
      REFERENCES
      INNOVATION
      KNOWLEDGE
      CONTACT
      ABOUT
      SERVICE & SUPPORT

      © 2026 Henkel Polybit Industries Limited