Skip to Content
Recent searches
      Bituplus Ultra E4180 packshot

      Bitumen-tom (membranes, primers)

      POLYBIT BITUPLUS ULTRA E 4180
      SBS modified bituminous waterproofing membrane

      Elastomeric high performance bitumen based torch applied waterproofing membrane.
      • High flexibility even in low temperature
      • Easy application on corner details.
      • Excellent adhesion on vertical surfaces

      TDS (1)

      SDSS (2)

      Request a consultation
      We have you covered
      Request a consultation

      Product Description

      POLYBIT® BITUPLUS ULTRA E4180 membrane is typically used for waterproofing / dampproofing of building basements , pileheads , concrete foundations, building Footings, bridge piers, bridge viaducts, underpasses , box culverts, retaining walls and holding tanks & reservoirs.
      Available pack size: 4mm
      • High flexibility even in low temperature
      • Easy application on corner details.
      • Excellent adhesion on vertical surfaces
      • Good dimensional stability under tension.
      • High mechanical strengths and fatigue resistance properties
      • Polymer rich compound. Easy and strong seal on overlaps.
      Bituplus Ultra E4180 packshot
      Bituplus Ultra E4180 packshot

      How to Use

      SURFACE PREPARATION & PRIMING

      The surface shall be cleaned thoroughly of all contaminants like dust, traces of curing compound, oil and grease. All surface imperfections, protrusions, structurally unsound and
      friable concrete must be removed and repaired.
      Apply Polyprime SB* (Solvent based primer) @4-6 m²/L to a clean, smooth and dry surface by brush, roller or spray.
      Allow the primer to dry prior to the application of the membrane. The primer promotes the adhesion between the membrane and the concrete surface.

      ALIGNMENT & TORCHING

      Start the installation of all membrane plies from the low point or drains, so that the flow of water is over or parallel to the plies, but never against the laps. All overlaps at the membrane seams shall be installed so as to have “up” slope laps over “down” slope laps. Begin membrane application by unrolling the roll of Bituplus E 4180 membrane and aligning the side laps. Side overlaps should be a minimum of 100 mm and the end overlaps 150mm.
      Bituplus ULTRA E 4180 membrane is installed by using a cylinder fed propane gas torch. Use of hand-held roofing torch is recommended as it affords a good control. Begin torching the embossed polyethylene side of the rolled portion of the membrane. As the membrane is heated the embossing starts to melt away exposing a shiny bitumen surface. Roll forward the membrane and press firmly with the boot or roller against the substrate to bond well. The propane flame should be moved from side to side and up the lap edge while the membrane is slowly unrolled and adhered to the underlying surface. Caution: Do not over torch the membrane as this will expose the reinforcement and cause damage to it.

      3.PROTECTION

      Bituplus ULTRA E4180 membrane shall be protected from getting damaged due to the ongoing site activities and during the backfilling process. Membranes laid on horizontal surfaces can be protected by a cement sand
      screed (50mm thick). On vertical surfaces the membrane has to be protected with Bituboard. Bituboard can be fixed on the membrane by torching the underside of the board.
      Please contact our technical service team for specific requirement.

      Frequently asked questions

      It is recommended using solvent based bitumen primer conforming to ASTM D 41

      Yes. It msut be protected from damages that may happen during the site activities.

      No. It is not necessary to use bonding agents or twin sided tape for fixing on torch applied membranes. It can be applied by torching.

      Works Well With
      • ${/content/heliux/adhesive/polybit/com/en/products/waterproofing-solutions/protection-membranes/product#/polybit-bituboard/SAP_0201W1P34GA5/searchResult.productFields.MainImageAltText}
        POLYBIT Bituboard

        A multi layer, asphaltic protection board manufactured by thermally bonding polymer modified bitumen with selected additives which, sandwiched between a layer of saturated fibre-glass on one side and anti-stick polyethylene liner on the other. 
      • ${/content/heliux/adhesive/polybit/com/en/products/waterproofing-solutions/bitumen-thin-coatings/product#/polybit-polyprime-sb/SAP_0201WEP345J0/searchResult.productFields.MainImageAltText}
        POLYBIT POLYPRIME SB

        A quick drying solvent based low viscosity bitumen primer. It is used as a primer coat on masonry and concrete substrates to improve the adhesion of bitumen based membranes and coatings. 

      Related Articles
      View all
      • Bitustick Cool

        The Next Generation of Performed Bituminous Coatings 
      • Foundations and Flooring Systems

        Discover, feel and touch our systems, through our mockup simulation boxes 
      • Wet Areas and Flooring Systems

        Discover, feel and touch our systems, through our mockup simulation boxes 
      • Polycryl FR

        The Ultimate Fire Rated Coating Solution 
      • Polycryl PF

        Strong UV protection For Polyurethane Foam Roof  
      • Bituplus Ultra

        The Ultimate Torch On Membrane Range 
      Sketch and drafting of a cozy house becoming real

      POLYBIT BITUPLUS ULTRA E 4180 IS PART OF OUR BIM MODELS

      Building Information Modeling (BIM) is an innovative approach to the planning, design, construction, and management of buildings and infrastructure. This smart model is a common source of knowledge for obtaining information about a building and provides a reliable basis for decision-making throughout the entire life cycle of a building, from conception to demolition.
      FIND OUT MORE
      Polybit Logo
      PRODUCTS
      SYSTEMS
      REFERENCES
      INNOVATION
      KNOWLEDGE
      CONTACT
      ABOUT
      SERVICE & SUPPORT

      © 2026 Henkel Polybit Industries Limited