Skip to Content
Recent searches
      Bituplus E4270 packshot

      Bitumen-tom (membranes, primers)

      POLYBIT BITUPLUS E 4270
      SBS modified bituminous waterproofing membrane

      Bituminous waterproofing membrane manufactured by blending a mixture of bitumen and SBS (Styrene Butadiene Styrene) polymers to obtain excellent waterproofing and low temperature flexibility properties.
      • Excellent resistance to positive water & vapor pressure
      • Excellent flexibility
      • High puncture and fatigue resistance

      TDS (1)

      SDSS (2)

      Request a consultation
      We have you covered
      Request a consultation

      Product Description

      POLYBIT® BITUPLUS E 4270 membrane is typically used for waterproofing / damp proofing of concrete foundations & footings, basements, pile heads, swimming pools & water retaining structures, tunnels, wet areas (kitchens & bathrooms).
      Available pack size: 4mm
      • Excellent resistance to positive water & vapor pressure
      • Excellent flexibility
      • High puncture and fatigue resistance
      • Excellent tensile and tear strength
      • High resistance against water borne chemicals
      • Good low temperature flexibility
      Bituplus E4270 packshot
      Bituplus E4270 packshot

      How to Use

      SURFACE PREPARATION & PRIMING

      The surface shall be cleaned thoroughly of all contaminants like dust, traces of curing compound, oil and grease. All surface imperfections, protrusions, structurally unsound and friable concrete must be removed and repaired with a suitable POLYCRETE* concrete repair mortar.
      Apply POLYPRIME SB* (Solvent based primer) @4-6 m²/lt to a clean, smooth and dry surface by brush, roller or spray. Allow the primer to dry prior to the application of the membrane. As the viscosity of
      the primer is low, it easily penetrates into the concrete pores. The primer promotes the adhesion between the membrane and the concrete surface. In addition to that, the primer also acts as a binder for the dust particles which gets accumulated on the concrete surface even after cleaning.

      ALIGNMENT & TORCHING

      Start the installation of all membrane plies from the low point or drains, so that the flow of water is over or parallel to the plies, but never against the laps.
      All overlaps at the membrane seams shall be installed so as to have "up" slope laps over "down" slope laps. Begin membrane application by unrolling the roll of BITUPLUS E 4270 membrane and aligning the side laps. Re-roll the roll halfway and stand on the unrolled portion to prevent shifting.
      Side overlaps should be a minimum of 100 mm and the end overlaps 150mm.
      BITUPLUS E 4270 membrane is installed by using a cylinder fed propane gas torch. Use of hand-held roofing torch is recommended as it affords a good control. Begin torching the embossed polyethylene side of the rolled portion of the membrane. As the membrane is heated the embossing starts to melt away exposing a shiny bitumen surface. Roll forward the membrane and press firmly with the boot or roller against the substrate to bond well. The propane flame should be moved from side to side and up the lap edge while the membrane is slowly unrolled and adhered to the underlying surface.

      3.PROTECTION

      BITUPLUS ULTRA E 4270 should be protected from getting damaged due to the ongoing site activities and during backfilling. Membranes laid on horizontal surfaces can be protected either by a cement sand screed (50mm thick) or by an asphaltic protection board (BITUBOARD)*. On vertical surfaces the membrane has to be protected with BITUBOARD. BITUBOARD can be fixed on the membrane by torching the underside of the board, or with a double sided bitumen adhesive tape (BITUTAPE TS)*.

      Frequently asked questions

      This is an epoxy grout

      No priming required.

      It can be applied at a thickness of 10 to 80mm/layer

      Works Well With
      • ${/content/heliux/adhesive/polybit/com/en/products/waterproofing-solutions/protection-membranes/product#/polybit-bituboard/SAP_0201W1P34GA5/searchResult.productFields.MainImageAltText}
        POLYBIT Bituboard

        A multi layer, asphaltic protection board manufactured by thermally bonding polymer modified bitumen with selected additives which, sandwiched between a layer of saturated fibre-glass on one side and anti-stick polyethylene liner on the other. 
      • ${/content/heliux/adhesive/polybit/com/en/products/waterproofing-solutions/bitumen-thin-coatings/product#/polybit-polyprime-sb/SAP_0201WEP345J0/searchResult.productFields.MainImageAltText}
        POLYBIT POLYPRIME SB

        A quick drying solvent based low viscosity bitumen primer. It is used as a primer coat on masonry and concrete substrates to improve the adhesion of bitumen based membranes and coatings. 
      • ${/content/heliux/adhesive/polybit/com/en/products/waterproofing-solutions/bitumen-tapes-membranes-flashing/product#/polybit-bitutape-ts/SAP_0201WCP34GD7/searchResult.productFields.MainImageAltText}
        POLYBIT Bitutape TS

        Bitutape TS is a non-reinforced twin side adhesive bitumen membrane which comprises of polymerized bitumen sandwiched between a plastic release film on either side. 

      Related Articles
      View all
      • Bitustick Cool

        The Next Generation of Performed Bituminous Coatings 
      • Foundations and Flooring Systems

        Discover, feel and touch our systems, through our mockup simulation boxes 
      • Wet Areas and Flooring Systems

        Discover, feel and touch our systems, through our mockup simulation boxes 
      • Polycryl FR

        The Ultimate Fire Rated Coating Solution 
      • Polycryl PF

        Strong UV protection For Polyurethane Foam Roof  
      • Bituplus Ultra

        The Ultimate Torch On Membrane Range 
      Sketch and drafting of a cozy house becoming real

      POLYBIT BITUPLUS E 4270 IS PART OF OUR BIM MODELS

      Building Information Modeling (BIM) is an innovative approach to the planning, design, construction, and management of buildings and infrastructure. This smart model is a common source of knowledge for obtaining information about a building and provides a reliable basis for decision-making throughout the entire life cycle of a building, from conception to demolition.
      FIND OUT MORE
      Polybit Logo
      PRODUCTS
      SYSTEMS
      REFERENCES
      INNOVATION
      KNOWLEDGE
      CONTACT
      ABOUT
      SERVICE & SUPPORT

      © 2026 Henkel Polybit Industries Limited