Skip to Content
Recent searches
      Polycoat RBE 1000 packshot

      Bitumen-thin coatings

      POLYBIT POLYCOAT RBE 1000
      SBS modified bitumen jellified emulsion

      Emulsified bituminous coating modified with high content of Styrene Butadiene Styrene rubber, which dries to form a tough and seamless, flexible water and vapor proof protective coating.
      • Cold applied
      • single component easy to apply
      • can be applied on damp substrates

      TDS (1)

      SDSS (4)

      Certificate Public (1)

      Request a consultation
      We have you covered
      Request a consultation

      Product Description

      POLYBIT® POLYCOAT RBE 1000Can be used for a wide variety of applications, which includes the following: waterproofing in wet areas such as toilets, kitchens etc. waterproofing & protective coating on concrete foundations & boundary wall footings. as damp proof membrane in sandwich construction. general vapor proof coating for both interior & exterior floors & walls. Avalaible sizes: 20L, 200L
      • Cold applied
      • single component easy to apply
      • can be applied on damp substrates
      • joint free
      • Solvent free
      Polycoat RBE 1000 packshot
      Polycoat RBE 1000 packshot

      How to Use

      Surface Preparation

      The surface shall be cleaned thoroughly of all contaminants like dust, traces of curing compound, oil, grease. Light mechanical grinding/grit blasting/high pressure water jet may be used to clean the surface of all the contaminants depending on the degree of contamination on the surface to be coated.

      Application

      t is highly recommended to apply a priming coat prior
      to the application of the Polycoat RBE 1000 coating on
      the substrate. The primer can be prepared in the site by
      diluting Polycoat RBE 1000 with 20% water. Depending on the dry film
      thickness required, apply the jellified emulsion. 2nd coat
      shall be applied only after the previous coat dries off.

      Finishing

      Polycoat RBE 1000 coating should be protected from
      getting damaged due to the ongoing site activities.
      coating can be protected either by a cement sand
      screed (50mm thick) or by an asphaltic protection board
      (Bituboard*).

      Frequently asked questions

      Substrate must be sound, free from dust, loose particles, oil, traces of curing coampound and any contamination. May be applied to damp but not waterlogged surfaces.

      There is no special primer. Primer can be prepared at site by diluting this product with 20% by volume of clean sweet water.

      No. It is a water based green product

      Works Well With
      • ${/content/heliux/adhesive/polybit/com/en/products/mortars-and-auxiliaries/concrete-repair/product#/polybit-polycrete-st/SAP_0201VLP34GH1/searchResult.productFields.MainImageAltText}
        POLYBIT Polycrete ST

        Polymer modified high strength cementitious repair mortar. Polymer modified repair mortar, specially formulated by blending OPC with non shrinking additives, fibers, polymers and fillers for repairing of beams, columns and slabs. 
      • ${/content/heliux/adhesive/polybit/com/en/products/mortars-and-auxiliaries/concrete-repair/product#/polybit-polycrete-fc/SAP_0201VLP34GG9/searchResult.productFields.MainImageAltText}
        POLYBIT Polycrete FC

        Polymer modified cementitious fairing coat single component polymer modified fairing coat designed to fill pores, blowholes, minor honeycombs on a concrete surface. 
      • ${/content/heliux/adhesive/polybit/com/en/products/waterproofing-solutions/protection-membranes/product#/polybit-bituboard/SAP_0201W1P34GA5/searchResult.productFields.MainImageAltText}
        POLYBIT Bituboard

        A multi layer, asphaltic protection board manufactured by thermally bonding polymer modified bitumen with selected additives which, sandwiched between a layer of saturated fibre-glass on one side and anti-stick polyethylene liner on the other. 

      Related Articles
      View all
      • Bitustick Cool

        The Next Generation of Performed Bituminous Coatings 
      • Foundations and Flooring Systems

        Discover, feel and touch our systems, through our mockup simulation boxes 
      • Wet Areas and Flooring Systems

        Discover, feel and touch our systems, through our mockup simulation boxes 
      • Polycryl FR

        The Ultimate Fire Rated Coating Solution 
      • Polycryl PF

        Strong UV protection For Polyurethane Foam Roof  
      • Bituplus Ultra

        The Ultimate Torch On Membrane Range 
      Sketch and drafting of a cozy house becoming real

      POLYBIT POLYCOAT RBE 1000 IS PART OF OUR BIM MODELS

      Building Information Modeling (BIM) is an innovative approach to the planning, design, construction, and management of buildings and infrastructure. This smart model is a common source of knowledge for obtaining information about a building and provides a reliable basis for decision-making throughout the entire life cycle of a building, from conception to demolition.
      FIND OUT MORE
      Polybit Logo
      PRODUCTS
      SYSTEMS
      REFERENCES
      INNOVATION
      KNOWLEDGE
      CONTACT
      ABOUT
      SERVICE & SUPPORT

      © 2026 Henkel Polybit Industries Limited