Skip to Content
Recent searches
      teaser polycryl fr

      Acrylic coatings (liquids)

      POLYBIT POLYCRYL FR
      Acrylic based, class A fire rated, flexible vapor proof protective coating

      Acrylic based single component, class A fire-rated protective coating especially designed as moisture vapor barrier on facades application.
      • Class A fire rated
      • Environmentally friendly. Low VOC
      • Single component

      TDS (1)

      SDSS (4)

      Request a consultation
      We have you covered
      Request a consultation

      Product Description

      POLYBIT® POLYCRYL FR Can be used as vapor / damp proof coating for facade cladding system, damp proof membrane is sandwich constructions , vapor proof barrier coating for interior & exterior floor & walls.
      Available pack size: 15L
      • Class A fire rated
      • Environmentally friendly. Low VOC
      • Single component
      • Good abrasion resistance properties
      • Excellent adhesion on most porous and nonporous substrates
      • Excellent resistance to vapor and moisture
      POLYBIT polycryl fr frontside imea
      teaser polycryl fr

      How to Use

      APPLICATION CONDITIONS & SURFACE PREPARATION

      The application temperature should be between 5°C to
      45°C. Application procedures may vary slightly depending
      upon site conditions.
      The surface shall be cleaned thoroughly of all contaminants
      like dust, traces of curing compound, oil and grease. Light
      mechanical grinding/grit blasting/high pressure water jet
      may be used to clean the surface of all the contaminants
      depending on the degree of contamination on the surface
      to be coated. All surface imperfections and protrusions
      shall be removed and repaired. Structurally unsound and
      friable concrete must be removed and repaired with a
      suitable Polycrete* concrete repair mortar.

      PRIMING

      A primer coat is recommended, particularly on the vertical
      surfaces to seal the pores and stabilize the surface. The
      primer coat can be made in the site by diluting the Polycryl
      FR 1 to 1 with water. The primer should be applied at a
      coverage rate of 4-5m2/L. On horizontal surfaces Polycryl
      FR can be applied directly without primer provided that
      recommended surface preparation has been carried out.

      MIXING & APPLICATION

      Polycryl FR is single component but stirring of the pail is
      recommended prior to the application of the coating. This
      will remove any sediment which may occur during storage.
      The use of a slow speed drill and suitable paddle should be
      used in order to avoid the formation of air bubbles.
      Apply the coating with a brush, roller or airless spray.
      Allow the coating to dry completely before applying the subsequent coats. 2 coats should always be applied; the
      second coat at 90° to the first. We recommend that a nonwoven geo-textile membrane be embedded into the first
      coat whilst it is still wet at all expansion joints projections
      and corner fillets to reinforce these areas. Allow the final
      coating to cure fully (72 hours) after which it can be put
      in service. For roof applications, the coating should be
      applied @1.1 L/m2/coat for a DFT of 1.5mm in 2 coats.
      As a protective coating, vapor barrier on concrete/render/
      plaster surfaces, the coating should be applied @0.70 L/
      m2/coat for a DFT of 1mm in 2 coats.

      Frequently asked questions

      There is no special primer. Primer can be prepared at site by diluting this with clean sweet water in the ratio 1:1 by volume.

      It falls under fire Class A as per ASTM E 84 & A2-S1, d0 as per EN 13501-1

      Yes. It is a civil defense approved product

      Works Well With
      • ${/content/heliux/adhesive/polybit/com/en/products/mortars-and-auxiliaries/concrete-repair/product#/polybit-polycrete-st/SAP_0201VLP34GH1/searchResult.productFields.MainImageAltText}
        POLYBIT Polycrete ST

        Polymer modified high strength cementitious repair mortar. Polymer modified repair mortar, specially formulated by blending OPC with non shrinking additives, fibers, polymers and fillers for repairing of beams, columns and slabs. 

      Related Articles
      View all
      • Bitustick Cool

        The Next Generation of Performed Bituminous Coatings 
      • Foundations and Flooring Systems

        Discover, feel and touch our systems, through our mockup simulation boxes 
      • Wet Areas and Flooring Systems

        Discover, feel and touch our systems, through our mockup simulation boxes 
      • Polycryl FR

        The Ultimate Fire Rated Coating Solution 
      • Polycryl PF

        Strong UV protection For Polyurethane Foam Roof  
      • Bituplus Ultra

        The Ultimate Torch On Membrane Range 
      Sketch and drafting of a cozy house becoming real

      POLYBIT POLYCRYL FR IS PART OF OUR BIM MODELS

      Building Information Modeling (BIM) is an innovative approach to the planning, design, construction, and management of buildings and infrastructure. This smart model is a common source of knowledge for obtaining information about a building and provides a reliable basis for decision-making throughout the entire life cycle of a building, from conception to demolition.
      FIND OUT MORE
      Polybit Logo
      PRODUCTS
      SYSTEMS
      REFERENCES
      INNOVATION
      KNOWLEDGE
      CONTACT
      ABOUT
      SERVICE & SUPPORT

      © 2026 Henkel Polybit Industries Limited