POLYBIT Polyseal CR PG

2 part chemical resistant polysulphide joint sealant

  • High resistance against industrial chemicals,
    hydrocarbon fuels and effluents
  • Highly resilient with excellent recovery characteristics
  • Provides permanent and uniform watertight seal

Features and benefits

2 part chemical resistant polysulphide joint sealant with chemical, fuel & effluents resistant joint sealant with higher flexibility.

Properties

Description

POLYBIT® POLYSEAL CR is a two component, chemical resistant polysulphide joint sealant. POLYSEAL CR is specifically designed to be used as a watertight seal for moderate movement and control joints in areas subjected to industrial chemicals, hydrocarbon fuels and effluents. It is based on a liquid polysulphide polymer which when mixed with the hardener, cures to form a tough, flexible and non staining rubber like seal. POLYSEAL CR has excellent adhesion to concrete, stone, metals and other common building substrates. The cured sealant has good resistance to deterioration on prolonged exposure to UV. POLYSEAL CR is available in two different grades. POLYSEAL CR black is resistant to chemical and sewage effluents. POLYSEAL CR grey is resistant to hydrocarbon fuels. The sealant has a movement accomodation actor (MAF) of ±25%. Available Pack: 4L/KIT

Documents and downloads

How to use

Surface Preparation and priming

The joint surface must be clean, dry and free from oil, loose particles, cement laitance and other contaminants which may affect the adhesion.The compressible joint filler shall be cut back to expose a uniform joint depth.

Primer should be applied to clean, dry surface prior to the installation of backer rod or bond breaking tape. Polyprime PS* is recommended to be applied on porous substrates. For non-porous substrates such as steel or glass, use Polyprime NP* for optimum adhesion. The primer shall be applied by a brush in a thin coat application and shall be allowed to become tack free prior to the application of the sealant. The joint edges shall be re-primed if the sealant installation is not carried out within 3 hours of application of the primer. For obtaining a clean and neat finish, masking tape shall be applied on both the edges of the groove before applying the primer

Back-up material

A bond breaking backing rod (Polyrod)* shall be inserted into all movement joints to avoid a three sided adhesion. Use of a backing rod will ensure proper joint depth and at the same time facilitate the formation of an hour glass profile on the applied sealant. The backer rod will also provide resistance to sealant tooling pressure and help to attain proper wetting of the substrate when the sealant is being tooled. The backing rod being inserted into the joint shall be of a diameter which is at least 20% larger but not greater than 33% of the joint width. This will ensure that the backer rod remains in compression and in place during sealant installation. For static and joints where the depth is not sufficient for the use of the backing rod, a bond breaking tape may be applied to prevent the three side adhesion. 

Mixing and Application

Pouring grade: Polyseal CR pouring grade is supplied in preweighed two parts pack, which requires on site mixing by pouring the hardener (Part B) into the base (part a) pail. Mix the material thoroughly with a slow speed drill (300-400 rpm) fitted with a flat bladed paddle for 1-3 minutes till a uniform colour and consistency is achieved.DO NOT PART MIX. Since the base and the curing agent ratio controls the ultimate physical properties like adhesion, durability and strength, one complete kit has to be mixed at a time. The side and base of the container shall be periodically scrapped with a scrapper to ensure that the curing agent is properly dispersed and blended into the mix. Load the gun grade sealant immediately into the barrel gun by a heavy duty follower plate. Start extruding into the joint firmly by maintaining an even pressure on the trigger of the gun. On vertical joints, sealant extrusion shall start from the bottom of the joint and continued to the top. For deep vertical joints, the sealant shall be filled in 2 to 3 applications in order to avoid air entrapment and sagging. The pouring grade material can be poured directly into the joint from the pail. Once the sealant has been installed a suitable rounded tool soaked in a soapy water solution can be used to achieve a smooth hour glass profile. Any masking tape applied should be removed immediately after the sealant is installed 

Related articles

  • Bitustick Cool

    The Next Generation of Performed Bituminous Coatings 

  • Foundations and Roofing Systems

    Discover, feel and touch our systems, through our mockup simulation boxes 

  • Wet Areas and Flooring Systems

    Discover, feel and touch our systems, through our mockup simulation boxes 

  • Polycryl FR

    The Ultimate Fire Rated Coating Solution 

  • Polycryl PF

    Strong UV protection For Polyurethane Foam Roof  

  • Bituplus Ultra

    The Ultimate Torch On Membrane Range 

Related products

  • ${/content/heliux/adhesive/polybit/com/en/products/central-pdp#/polybit-polyprime-ps/SAP_0201P1P34GL7/searchResult.productFields.MainImageAltText}
    POLYBIT Polyprime PS
    Seals the joint surface and increase the adhesion with the joint sealant. 
  • ${/content/heliux/adhesive/polybit/com/en/products/central-pdp#/polybit-polyrod/SAP_0201P1P345J2/searchResult.productFields.MainImageAltText}
    POLYBIT POLYROD
    Non absorbent backing rod to maintain proper width to depth ratio and avoid 3 side adhesion of sealants. 
  • ${/content/heliux/adhesive/polybit/com/en/products/central-pdp#/polybit-polyboard/SAP_0201P1P34GE6/searchResult.productFields.MainImageAltText}
    POLYBIT Polyboard
    Polyboard is a compressible bitumen impregnated fibre board for expansion joints. 

Frequently asked questions

Yes. It is a non-toxic sealant

Type M, Grade P, Class 25%,
USE T

Compatible with elastomeric emulsion paints