POLYBIT Polypoxy SL20

Epoxy resin based self levelling floor topping

  • Self Levelling
  • Good resistance to a wide range of chemicals
  • Seamless floor, which helps in keeping the microbial
    count low

Features and benefits

A three component, solvent free, epoxy based self levelling floor topping which provides a chemical resistant and hygienic surface.

Properties

Description

POLYBIT® POLYPOXY SL 20 is used to provide a heavy duty floor screed for: laboratories; plant room for pharmaceutical and health care product manufacturing units; operation theatres; food & beverage manufacturing industries; light industrial plants. Available pack size: 15L kit.

Documents and downloads

How to use

Surface Preparation

Clean the surface of all dust, dirt, oil & grease, cement laitance and all loosely adhering particles. New concrete surface shall be at least 28 days old and the surface moisture content less than 5%. Surface irregularities and blow holes shall be repaired with Polypoxy BF or Polycrete ST. The surface after carrying out the necessary cleaning shall be vacuumed for removing the dust debris left over after the cleaning process. The surface shall be primed with Polyprime EP @ 4-5 m2/L. For highly porous substrates, a 2nd coat may be required. The coating shall be applied within 24 hours of application of the primer. If the primer surface is left open for more than 24 hours, then a fresh coat of primer has to be re-applied.

Application

Polypoxy SL 20 is supplied in three pre-weighed packs. Part mixing is strictly prohibited. Take a suitable container and pour the resin (A) into it. Add the hardener (B) into the resin and mix thoroughly with a paddle mixer. Use of a slow speed drill is recommended to reduce the formation of air bubbles. Then slowly add the filler (C) into the container and mix thoroughly for a few minutes. Ensure sufficient labor and material is available at site to ensure a smooth continuity of the application of the flooring. Apply the Polypoxy SL 20 topping, by pouring on to the primed surface and spread with a steel notched trowel to achieve a 1mm to 4mm seamless topping. Once the material is evenly spread, continuous spiking with a spiked roller is to be done to remove all entrapped air. Spiking adjacent layers is recommended to be done at 50% overlaps.
CAUTION
– do not use below 5°C
– over troweling is to be avoided
– Polypoxy SL 20 should not be applied to surfaces which has rising dampness and there is a phenomenon of reverse osmosis. In addition to that, application is always recommended to be carried out when the atmospheric temperature is low. 

Finishing

Store in a dry, cool and shaded area. Protect from sunlight, frost and high humidity. In tropical climates, store the material in air conditioned area at less than 25°C. The shelf life of the product is 12 months if stored as per recommendations. Exposure to heat and high humidity will result in the premature deterioration of the product and reduce its shelf life considerably 

Related articles

  • Bitustick Cool

    The Next Generation of Performed Bituminous Coatings 

  • Foundations and Roofing Systems

    Discover, feel and touch our systems, through our mockup simulation boxes 

  • Wet Areas and Flooring Systems

    Discover, feel and touch our systems, through our mockup simulation boxes 

  • Polycryl FR

    The Ultimate Fire Rated Coating Solution 

  • Polycryl PF

    Strong UV protection For Polyurethane Foam Roof  

  • Bituplus Ultra

    The Ultimate Torch On Membrane Range 

Related products

  • ${/content/heliux/adhesive/polybit/com/en/products/central-pdp#/polybit-polyprime-ep/SAP_0201TNP34GL4/searchResult.productFields.MainImageAltText}
    POLYBIT Polyprime EP
    It is a two component solvent free epoxy resin based primer and sealer for epoxy and polyurethane based coatings and toppings. It can also be applied as a scratch coat with the addition of graded quartz sand. 
  • ${/content/heliux/adhesive/polybit/com/en/products/central-pdp#/polybit-polypoxy-bf/SAP_0201TWP34GK0/searchResult.productFields.MainImageAltText}
    POLYBIT Polypoxy BF
    It is a two component, solvent free, epoxy based repair putty and mortar for concrete surfaces. The epoxy putty consists of graded fillers and non-sagging agents. It is designed for filling of blow holes, cracks and minor imperfections on concrete surfaces. 
  • ${/content/heliux/adhesive/polybit/com/en/products/central-pdp#/polybit-polypoxy-nf/SAP_0201WUP34GK8/searchResult.productFields.MainImageAltText}
    POLYBIT Polypoxy NF
    Easy to use non-flowing, sand filled two component epoxy compound which can be used for bedding, gap filling, repair and adhesive applications. 

Frequently asked questions

Yes. Solvent free epoxy based primer to be used

1L can cover 1 sqm at 1mm thickness

Yes. This product is highly abrasion resistant