POLYBIT BITUPLUS ULTRA P 4270

APP Modified Bitumen Waterproofing Membrane

  • Polymer rich compound. Easy and strong seal on overlaps
  • High flexibility
  • High softening point

Features and benefits

Plastomeric membrane with excellent heat & UV resistance and waterproofing properties.

Properties

Description

POLYBIT® BITUPLUS ULTRA P 4270 is used as a waterproofing membrane on the following structures, inverted roofs & podiums, terraces & balconies, sunken slabs, bridge piers, bridge viaducts, underpasses, box culverts, concrete foundations, building footings, retailing walls, holding tanks & reservoirs.
Available pack size: 4mm

Documents and downloads

How to use

SURFACE PREPARATION

The surface shall be cleaned thoroughly of all contaminants like dust, traces of curing compound, oil and grease. All surface imperfections, protrusions, structurally unsound and friable concrete must be removed and repaired.

Priming & Alignment

Apply Polyprime SB* (solvent based primer) @ 4-6 m²/L to a clean smooth and dry surface by brush, roller or spray. Allow the primer to dry prior to the application of the membrane.
Start the installation of all membrane plies from the low point or drains, so the flow of water is over or parallel to the plies, but never against the lap. All overlaps at the membrane seams shall be installed so as to have
“up” slope laps over “down” slope lap. Begin membrane application by unrolling the roll of Bituplus P membrane and aligning the side laps. Side overlaps should be a minimum of 100 mm and the end overlap 150mm. 

Torching

Bituplus ULTRA P 4270 membrane is installed by using a cylinder fed propane gas torch. Use of hand-held roofing torch is recommended as it affords a good control. Begin torching the embossed polyethylene side of the rolled portion of the membrane. As the membrane is heated the embossing starts to melt away exposing a shiny bitumen surface. Roll forward the membrane and press firmly with the boot or roller against the substrate to bond well. The propane flame should be moved from side to side and up the lap edge while the membrane is slowly unrolled and adhered to the surface. 

Related articles

  • Bitustick Cool

    The Next Generation of Performed Bituminous Coatings 

  • Foundations and Roofing Systems

    Discover, feel and touch our systems, through our mockup simulation boxes 

  • Wet Areas and Flooring Systems

    Discover, feel and touch our systems, through our mockup simulation boxes 

  • Polycryl FR

    The Ultimate Fire Rated Coating Solution 

  • Polycryl PF

    Strong UV protection For Polyurethane Foam Roof  

  • Bituplus Ultra

    The Ultimate Torch On Membrane Range 

Related products

  • ${/content/heliux/adhesive/polybit/com/en/products/central-pdp#/polybit-polyprime-sb/SAP_0201WEP345J0/searchResult.productFields.MainImageAltText}
    POLYBIT POLYPRIME SB
    A quick drying solvent based low viscosity bitumen primer. It is used as a primer coat on masonry and concrete substrates to improve the adhesion of bitumen based membranes and coatings. 
  • ${/content/heliux/adhesive/polybit/com/en/products/central-pdp#/polybit-bituboard/SAP_0201W1P34GA5/searchResult.productFields.MainImageAltText}
    POLYBIT Bituboard
    A multi layer, asphaltic protection board manufactured by thermally bonding polymer modified bitumen with selected additives which, sandwiched between a layer of saturated fibre-glass on one side and anti-stick polyethylene liner on the other. 

Frequently asked questions

It is recommended using solvent based bitumen primer conforming to ASTM D 41

Yes. It msut be protected from damages that may happen during the site activities.

No. It is not necessary to use bonding agents or twin sided tape for fixing on torch applied membranes. It can be applied by torching.